ARMORPATCH 300
TWO COMPONENT WATER RESISTANT
CONCRETE REPAIR MORTAR
Product Description
ARMORPATCH 300 is a two-component, water
resistant corrosion inhibiting, polymer-modified
shrinkage compensated, rapid setting, high strength
mortar specially formulated for structural concrete
repairs in vertical and horizontal surfaces.
ARMORPATCH 300 has impressive water repellent and
waterproofing properties and therefore suitable for
areas requiring waterproofing
- Water repellent and waterproof
- A Recommended for areas requiring moisture
remediation - Aesthetically nice self leveling and smooth
finish - Fiber reinforced to eliminate crack and
increase strength - Good corrosion Inhibition property, therefore
protect reinforcements - Minimal shrinkage and outstanding resistance
to crack - Excellent bond strength
- High abrasion resistance
- ARMORPATCH 300 can be used for all structural
concrete repairs such as: - Interior and exterior concrete surfaces
- Repair of horizontal and vertical surfaces
- Repair concrete sidewalks, concrete spalling
- Parking lots and bridge decks
- Fast setting and curing, can be put to use in few
hours ( depending on temperature) - Industrial floors
ARMORPATCH 300 is packed in 20 kg and 25kg bags.
Store in a cold dry place. With proper storage
material can be stored and used within 12 months.
MIXING : Pour 3.3 to 3.8 litres of water into a clean
plastic or metal bucket , pour 70% of ARMORPATCH
300 into the clean bucket of water, then mix with a
power mixer at 400 RPM, after two minutes of
mixing pour the rest of the material and mix until
full homogeneity is achieved
Armorsil provides detailed method statements
on all its products for use in various applications.
Below is an information summary for guidance
Pourthematerialonthearea to be resurfaced using a
hand trowel or spray gun ,because of the self
leveling property of ARMORPATCH 300 the material
can easily be finished as desired, using either a
trowel or a broom. The level of thickness will also be
determined by the application need, but should be
achieved in one application; the mixed material can
be applied at a thickness between 3mm and 20 mm.
If the mix hardens, it should be disposed, please do
not attempt to remix or add water to hardened mix
Conforms to the requirements of BS EN 934-2
Table 9
Appearance: White
Like all material that contains Portland cement,
this material must be handled professionally as
it can cause irritation and burns. Therefore
contact with skin and eyes must be avoided.
All recommendations, statements and technical data herein are based on tests we believe to be reliable and correct, but
accuracy and completeness of said tests are not guaranteed and are not to be construed as a warranty either expressed or
implied. User shall rely on his or her own information and tests to determine suitability of the product for the intended use and user assumes all risk and liability resulting from his or her use of the product. Nothing contained in any supplied materials relieves the user of the obligation to read and follow the warnings and instruction for each product as set forth in the current Technical Data Sheet, product label and Safety Data Sheet prior to product use away. Armorsil Manufacturing supplies products that comply with the properties shown on the current datasheets. In the unlikely event that products supplied are proved not to comply with these properties, then we will replace the non-compliant product or refund the purchase price. Armorsil Manufacturing does not warrant or guarantee the installation of the products as it does not have control over the installation or end use of the products. Any suspected defects must be reported to Armorsil Manufacturing in writing within seven working days of being detected. Armorsil Manufacturing. Makes no warranty as to merchantability or fitness for a particular purpose and this warranty is in lieu of all other warranties express or implied. Neither seller nor Armorsil Manufacturing shall be liable to the buyer or any third person for any injury, loss or damages of any sort including remote or consequential damages, down time, or delay directly or indirectly resulting from use of or inability to use the product. . The information contained in the latest data sheet supersedes all previously published editions. Visits to site by Armorsil personnel do not constitute supervisory responsibility. Armorsil reserves the right to alter the information contained in this datasheet without prior notice
